A fine example of the Spakrman and Stevens Swan 41, she has been sympathetically restored and upgraded over the last 20 years by its current and previous owner. All improvements have been made with originality in mind and have been to improve functionality and keeping the aesthetics. Trinket has part 1 of the UK small ships registry, giving proof of ownership and is renewed every 5 years.
Please contact at +44 (0)1326 211007
Características adicionales, equipo e información:
Nombre del barco
Forma del casco: Otro
GROUND TACKLE 20kg Bruce anchor stows in bow roller with 60cm of 12mm chain 15kgm CQR anchor is stowed deck forward of the mast (kedge anchor) The chain and warp for kedge anchor is stowed under the helmsman seat A light weight aluminium Danforth anchor is also carried
Safety Equipment - available on separate spreadsheet
RIGGING The original Nautor mast and boom are fitted. The mast was rewired with new LED tricolour and anchor light, motoring and spotlight in about 2008. All standing rigging was renewed 2012. ( The original rigging wires with Norseman terminals are included as spares). A Harken mainsail track system was fitted by the previous owner with recirculating ball cars.
The boom was converted to slab reefing in 2008, with a sheave box fitted to the aft end with sheaves for 2 reefs. An additional sheave is fitted to the side of the boom for the third reef. A three section rope jammer was fitted under the boom to secure the reefing lines. A new gooseneck plate was fitted to the mast for the fixed gooseneck. ( The original design had the gooseneck running on a track on the mast for the boom downhaul.) A three sheave block leads the reefing lines to a deck mounted snatch block, and then to the reefing winch.
The genoa roller reefing system was replaced new in 2007 with a Facnor system. The reefing drum was replaced with the latest Facnor drum in 2013, as the original drum had seized bearings. The original rig for the Swan 41 had a large 150% genoa. In order to improve performance in strong winds, the current owner designed a furling jib system which can be used when the genoa is furled. This is a portable stay with continuous line roller reefing which is normally stowed by the mast. When stowed , the genoa can be tacked normally. In order to used the jib, the stay is transferred to the fixing on the deck track just aft of the fixed forestay. It is tightened using a screw backstay type tensioner. The high cut jib can then be hoisted into the foil, and furled/reefed using the continuous line furler, with the furling line taken aft to the cockpit.
This system has greatly enhanced the flexibility of the rig, and was extensively tested in a round Atlantic voyage in 2011. In winds above force 4, windward performance is improved by using the jib rather than the reefed genoa. The Harken backstay tensioner ( manual type operated using a winch handle) was replaced in 2012. The original Lewmar mainsheet system was replaced with a Harken recirculating ball type in 2007.
Two spinnaker poles are supplied. One is the original Nautor pole. The other is a carbon pole with Harken fittings that is half the weight of the aluminium pole. This was reconditioned in 2010. The original reaching pole is supplied. New genoa sheets and furling line 2016
As new 150% laminate genoa only used several times Identical laminate genoa with the foot cut about 1m higher for better visibility when cruising. Worn but still useable. Good quality Dacron 150% genoa with double ply leach, older sail but still in good condition Brand new laminate mainsail (never used) Identical laminate mainsail now worn but now delaminating. This is the usual mainsail used when cruising Good quality Dacron mainsail and was used regularly when cruising in tropical water High cut jib new in 2008, used regularly but still in good condition Spinnaker in sock as new condition.
ENGINE Engine Brand: Perkins Engine Model: 4-108 Engine Type: Inboard Engine/Fuel Type: Diesel Location: Centre Propeller: 2 blade propeller Drive Type: Shaft Drive Engine Power: 50 HP Propeller shaft replaced in 2008 Flexible coupling (Vetus) fitted in 2008 Maxprop 2 blade feathering propeller was reconditioned in 2013 Stern bracket bearing replaced in 2013 Volvo shaft seal replaced in 2013 Believed to have had a total rebuilt in 2006 by a previous owner, completely re wired in 2012, engine ventilation blower replaced in 2015. Engine log kept over the last 20 years
ELECTRICS & EQUIPMENT ICOM main VHF with DSC Wind speed and direction Chart plotter is fitted with various packs for UK, Biscay, Spain, Portugal, Atlantic Islands, Brazil and Caribbean Islands GPS Depthsounder Navigation centre Log-speedometer BandG Hercules Autopilot with Autohelm linear drive operating directly on the rudder quadrant. Sperate flux gate compass. High output alternator fitted in 2011 with smart controller (Driftgate) Rewired in 2013
DINGHY & OUTBOARD - Available by separate negotiation
1976 Nautors Swan 41 - TRINKET
Sparkman and Stevens design GRP hull (repainted with Awlgrip in 2013) original design deck and cockpit, teak decks and finish in the cockpit were all replaced in 2006. Steering pedestal rebuilt and repainted in 2012 A section of stainless steel track has been fitted in the bow to provide an attachment for the furling jib stay. This is backed by a stainless plate under the deck, and is also tied to the stem fitting. The forward Dorade ventilator box has been removed. The forward sliding hatch has been replaced by a Lewmar opening hatch. A Goiot manual anchor windlass has been fitted. A deck plate secures the Bruce main anchor Cockpit lockers have been added. All the aluminium toerails were replaced in 2013, using original Nautor parts. These included all new fastenings with insulating washers to avoid corrosion. All the stanchion bases were replaced, with 4 new Nautor stanchions. (The remainder were reconditioned) Guard rail wires were renewed in 2016.
DIMENSIONS LOA 41ft 0in Beam 11ft 11in Maximum Draft 6ft 7in
The original layout has been maintained, with the exception of the forward cabin The forward cabin originally comprised of two fold down 'pipe cots' with sail bins underneath. Proper bunks were constructed using solid teak fronts. The sails bins are still accessible by lifting the bunk boards. The heads compartment was re painted using Awlgrip (sprayed) in 2014, the original dome lights have been replaced with LED lights. In addition 5 florescent lights have been fitted.
Original Taylor cooking stove which was re conditioned in 2014 Original Baby Blake toilet is fitted and completely rebuilt with all parts epoxy coated in 2014 Sump tank was replaced by an electric tank in 2016 Loudspeakers in the cabin and cockpit Broadband masthead active antenna is fitted A pressure water system is fitted, this supplies hot and cold water to the galley and heads. The water is heated from the engine providing 24 hour hot water.
Number of twin berths: 1 Number of double berths: 1 Number of cabins: 2 Number of heads: 1